Analysis of Reducing Loss Time in The Stamping Process in The AIDA 800 T Blanking Machine at PT. XYZ
DOI:
https://doi.org/10.29407/jmn.v6i1.19448Keywords:
losstime, Aida 800 T machine, cost reductionAbstract
In a production process optimization is needed to increase the productivity of production results. This research was conducted on the Aida 800T Blanking machine, based on the results of field observations made on the Aida 800T Blanking machine at PT. XYZ there is frequent losstime, this hinders the production process which results in reduced production targets. Losstime often occurs during a production process, the factors that often occur are the environment, humans, materials, and machines. The purpose of this study is to find out how much the cost is due to loss time. The methods used to perform losstime analysis are 5 why analysis, Pareto diagrams and fishbone diagrams to identify problems that often occur in the production process. From the results of the research, it was found that the costs incurred were Rp. 6,509,220. By performing a losstime analysis, there is a cost saving of 3,797,736 during one month of production, so that the method is successfully used with the end result of doing kaizen.
Downloads
References
S. D. Andryanto, "apa-itu-revolusi-industri-4-0-dan-society-5-0," TEMPO, 20 Mei 2021. [Online]. Available: https://tekno.tempo.co/apa-itu-revolusi- industri-4-0-dan-society-5-0/.
H. M. & Hasrul hasrul, "Analisa Kinerja Mesin Roughing Stand dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) dan Failure Mode Effect Analysis (FMEA)," Jurnal INTECH, vol. 3, p-ISSN. 2407-781X, 2017.
A. P. Takaria Kevin Leonardo, "Analisa Losstime untuk Meningkatkan Produktivitas pada PT. PMI," Jurnal Titra, vol. 7, no. Losstime Produktivitas, pp. 327-334, 2019.
R. M. Akhlis, "Analisis Proses Blanking dengan Simple Press Tool," Jurnal Rekayasa Mesin, vol. Vol.5, no. Proses Blanking, pp. 85-90, 2014.
D. Anon, "Understanding How to Use The 5-Whys for Root Cause Analysis," vol. 61, no. 5 why analysis, pp. 1-10, 2016.
T. &. K. Muhandri, "Sistem Jaminan Mutu Industri Pangan," Pangan, no. Industri pangan, 2006.
M. Nasution, "Manajemen Mutu Terpadu," Ghalia Indonesia, no. Manajemen Mutu Terpadu, 2004.
T.-C. Scarvada, "A Review of the Causal Mapping Practice and Research Literature," Second World Conference on POM, no. Causal Mapping Practice and Research Literature, 2004.
M. Imai, "Kaizen (Ky'zen) Kunci Sukses Jepang Dalam Persaingan,"PT.Pustaka Binaman Presindo, 2001.
F. &. A. D. Tjiptono, "Total Quality Management," 2001.
P. K. E. Sirine Hani, "Pengendalian Kualitas Menggunakan Metode Six Sigma," AJIE (Asian Journal of Innovation and Entrepreneurship), vol. Vol.02, no. Six Sigma, p. 03, 2017.
S. o. B. S. STORES, "JFS JSH440W JFS A1001," BBN STEEL STORES, 3Maret 2019. [Online]. Available: www.steelstores. [Accessed 18 November 2021].
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish with this journal agree to the following terms:
- Copyright on any article is retained by the author(s).
- The author grants the journal, right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work’s authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal’s published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
- The article and any associated published material is distributed under the Creative Commons Attribution-ShareAlike 4.0 International License
