Analysis of the Effect of Cooling Variations on the Hardness Value and Microstructure of ST 42 Steel from SMAW Welding Results
DOI:
https://doi.org/10.29407/noe.v8i01.23190Keywords:
baja ST 42, kekerasan, media pendinginan, SMAWAbstract
The purpose of the research is to find out how the effect of cooling media variations of air, water, and SAE 40 oil on the level of hardness and microstructure of SMAW welding results on ST 42 steel material. The type of research used in this research is experimental research with Quantitative methods. The results showed that the variation of cooling media had a significant effect on the hardness and microstructure of the SMAW welding results. The highest average hardness with water cooling media in the weld metal area was 125.080 Kgf/mm², the HAZ area was 111.375 Kgf/mm², the parent metal area was 129.429 Kgf/mm² while the lowest hardness with air cooling media in the weld metal area was 93.205 Kgf/mm², the HAZ area was 99.806 Kgf/mm², the parent metal area was 121.893 Kgf/mm². Furthermore, the results of testing the microstructure of ST 42 steel from SMAW welding with water cooling media in the HAZ (Heat Affected Zone) area show more and denser pearlite grains, this shows a strong correlation between the amount of distribution and density of pearlite grains with an increase in hardness of ST 42 steel material from SMAW welding, especially with water cooling media.
References
Ardiansah, A., & Yunus. (2019). Studi Hasil Proses Pengelasan FCAW ( Flux Cored Arc Welding ) Pada Mterial ST 41 Dengan Variasi Media Pendingin Terhadap Kekuatan Tarik dan Struktur Mikro. Jurnal Teknik Mesin, 7(2), 9–16.
Effendi, N. (2019). Struktur Mikro Dan Kekerasan Baja S45C Pada Pengelasan Smaw Dengan Variasi Media Quench. Jurnal Ilmiah Pendidikan Teknik Dan Kejuruan, 12(1), 30–37. https://doi.org/10.20961/jiptek.v12i1.28916
Irzal, I., Waskito, W., & Mulyadi, R. (2021). Pengaruh Jenis Media Pendingin Air Garam, Air Sumur, Oli Terhadap Hardness Pada Hasil Pengelasan Baja S45C Mengunakan Las Smaw. Jurnal Vokasi Mekanika (VoMek), 3(2), 34–40. https://doi.org/10.24036/vomek.v3i2.201
Maghfiroh, M. R., Soebiyakto, G., & Farid, A. (2019). Analisa Pengaruh Variasi Media Pendingin Air Dan Oli Pada Sambungan Lap Joint Terhadap Sifat Mekanik Menggunakan Las SMAW. Proton, 11(1), 35–42.
Muddin, S., Jamaluddin, J., Eka Putra, R., & Sahrul, S. (2021). Analisis Kekuatan Tarik Pengaruh Perlakuan Panas Hasil Pengelasan Kampuh V Baja 42 Dengan Media Pendingin Air Dan Oli. ILTEK : Jurnal Teknologi, 16(1), 6–10. https://doi.org/10.47398/iltek.v16i1.584
Pattiasina, N. H., Holle, S., & Keppy, I. H. (2018). Pelatihan Proses Pengelasan Menggunakan Mesin Las Listrik dalam Upaya Peningkatan Ketrampilan Pekerja di Desa Rumahtiga. Jurnal Simetrik, 8(1), 77–83. https://doi.org/10.31959/js.v8i1.90
Sebayang, A., Tarigan, E., & Siahaan, S. (2021). Analisa Perbandingan Kekuatan Tarik Hasil Pengelasan Baja ST 37 dengan Menggunakan Metode Pengelasan Shielded Metal Arc Welding (SMAW) dan Metal Inert Gas (MIG) Menggunakan Arus 140 A dan 120 A. Jurnal Ilmiah Core IT, 9(6), 1–8.
Sultoni, Finahari, N., & Sahbana, A. (2019). Analisa Pengaruh Variasi Media Pendingin Air Dan Oli Pada Sambungan Lap Joint Terhadap Sifat Mekanik Menggunakan Las SMAW. Proton, 11(1), 35–42.
Suyetno, A. (2020). Pengembangan Massive Open Online Courses (MOOCs) pada Materi Pengelasan. Jurnal Teknik Mesin Dan Pembelajaran, 2(2), 141–152. https://doi.org/10.17977/um054v2i2p141-152
Winardi, Y., Fadelan, F., Munaji, M., & Krisdiantoro, W. N. (2020). Pengaruh Elektroda Pengelasan Pada Baja AISI 1045 Dan SS 202 Terhadap Struktur Mikro Dan Kekuatan Tarik. Jurnal Pendidikan Teknik Mesin Undiksha, 8(2), 86–93. https://doi.org/10.23887/jptm.v8i2.27772
Zulfikar, A., Sasria, N., Putri, M., Lubis, D., & Dewanto, H. A. (2019). Pelatihan Dasar Dasar Pengelasan Bagi Warga Karang Joang Km 15, Balikpapan, Kalimantan Timur. Prosiding Sepakat Institut Teknologi Kalimantan, 1(1), 1–6. https://journal.itk.ac.id/index.php/sepakat/article/download/606/300
Downloads
Published
Issue
Section
License
Copyright (c) 2025 I Gede Wiratmaja, I Nyoman Pasek Nugraha, I Kadek Alit Mahayoga
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Copyright on any article is retained by the author(s).
- The author grants the journal, right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work’s authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal’s published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
- The article and any associated published material is distributed under the Creative Commons Attribution-ShareAlike 4.0 International License
How to Cite
